在线客服

网站公告: 保定市万嘉门窗制造有限公司坚持以诚信为本的理念,本着“同等价格比质量,同等质量比价格,同等价格、同等质量比服务。”的宗旨,为广大的新老客户打造出更完善的产品。

400-0312-611

保定市万嘉门窗制造有限公司

联系人:高先生 安女士

手 机:13803126757 13082332599

电 话:0312-5060303

邮 箱:13803126757@139. com

地址:河北省保定市北市区后辛庄工业区新民路39号

当前位置:断桥铝门窗质检检验五大标准
一、密闭性要求 A closed requirement 1、角部密封条(胶角):密封条应避免转角拼接,应将转角处密封条设计成90度整体式胶角。 1. Corner seal (glue corner) : seal strip should avoid corner splicing, and the corner seal should be designed as 90 degree integral glue Angle. 2、框扇密封条:开启扇部位宜设计三道密封胶条,分别为主密封胶条、扇压边胶条和框压边胶条。 2. Frame fan seal: open the fan part to design three sealing strips, which shall be the main sealing strip, the rubber strip of the fan and the rubber strip in the frame. 二、防渗漏要求 2. Prevention of leakage 1、外窗必须设置排水通道、排水口、排气孔(气压平衡孔),排出窗框扇内积水。排水口外侧应设扣盖,防止强风将雨水、灰尘吹入窗扇。 1. The external window must set drainage channels, drain holes and air holes (air pressure balance holes), and discharge the water in the window frame fan. The outside of the drain should be buttoned to prevent the strong wind from blowing rain and dust into the Windows. 2、隔热条应采用C型构造,与内外铝型材复合后在同一个水平面上,避免隔热条处积水造成渗漏、腐蚀隐患,同时可增加隔热条长度,提高热工性能。 Article 2, insulation should use C type structure, with internal and external aluminum compound in the same horizontal plane, avoid heat insulation article caused water leakage, corrosion hazard, at the same time can increase the insulation length, improve thermal performance. 3、门窗洞口尺寸:结构洞口预留不应过大,避免封堵困难造成渗漏隐患。 3. The size of the door and window hole: the structure hole should not be too large to avoid the trouble caused by the sealing difficulty. 4、企口:窗洞因为特殊原因,如外墙为石材幕墙,洞口预留尺寸大,结构洞口建议做企口,企口应与混凝土墙同时浇筑。 4. Tongue-opening: the window hole is for special reasons, such as the outer wall for the stone curtain wall, the hole is reserved for large size, the structure hole is recommended to do the enterprise mouth, the enterprise mouth should be poured in the concrete wall at the same time. 5、外窗台板:外墙材料为涂料的建筑,建议采用金属窗台板。金属窗台板内侧应压入窗框,外侧突出墙面做滴水。 5. External window board: the exterior wall material is the building of paint, the proposal USES metal window sill board. The inside of the metal window board should press the window frame, the outside highlight the wall to make the water. 6. 窗框与结构洞口:窗框宜立中安装,如靠外侧安装,应向内收进20mm,防止结构施工误差导致窗框安装在结构外皮以外,造成雨水渗漏。 Window frame and structure hole: the window frame is suitable for installation, if it is installed on the outside, it should be 20mm to the inside, prevent the construction error of the construction and cause the window frame to be installed outside of the structure, causing the water leakage. 三、 框扇结构要求 3. Frame fan structure requirements 1、组角:组角是关系到门窗整体性的重要工序。 Group Angle: the group Angle is the important procedure that relates to the whole door and window. 2、抹胶工艺:一般情况下应采用角码+抹组角胶工艺,窗角禁止未抹胶即挤压成型。 2. Glue process: in general, it is necessary to use the Angle code + wipe process, and the window Angle is forbidden to press the rubber. 3、注胶工艺:组角亦可采用角码+导胶槽+注胶孔+双组份注胶+角片工艺,保证角部强度要求,确保门窗成品在运输、安装后无变形移位现象的出现。 Group 3, injecting process: Angle can be adopted Angle code + glue tank + + a two-component adhesive hole injection glue + Angle slice technology, ensure corner strength requirements, to ensure that the doors and Windows after finished goods during transportation, installation no deformation displacement phenomenon to appear. 四、保温隔热要求 4. Thermal insulation requirements 1、型材的腔体设计:型材应采用多腔体结构,减少热量的流失,同时应使外窗隔热构件上下共面,形成整体隔热面,消除冷桥,阻断热量流失通道。 Design: 1, the profile of the cavity profile multi-cavity structure should be adopted, and reduce the loss of heat, and should be up and down outside the window insulation components coplanar, form the overall insulating surface, eliminate cold bridge, block heat loss channels. 2、玻璃安装槽内宜安装隔热胶条:增加空气腔室的数量,降低中空玻璃四周与型材之间的热量损失,提高整窗的保温效果。 2. Install insulation tape inside the glass installation groove: increase the number of air chamber, reduce the heat loss between the hollow glass and the profile, and improve the insulation effect of the whole window. 3、窗扇应采用T型隔热条设计:窗扇隔热条设计为T型,与中间胶条搭接,实现扇框连接处冷热分区。禁止将中间胶条直接搭在扇的铝型材上。 3. The window fan shall be designed with a t-shaped insulation bar: the window fan insulation bar is designed as a T type, which is connected with the intermediate glue-bar to realize the cold and hot zone of the fan frame connection. It is forbidden to put the intermediate glue bar directly on the aluminum section of the fan.
网站建设:保定遨游公司 版权所有 © 保定市万嘉门窗制造有限公司  手机网站
联系人:安经理 服务热线:400-0312-611 电话:0312-5060303 手机:13082332599 网址:HTTP://www.bdwjmc.com
地址:河北省保定市北市区后辛庄工业区新民路39号 友链:保定保洁 护坡砖模具