在线客服

网站公告: 保定市万嘉门窗制造有限公司坚持以诚信为本的理念,本着“同等价格比质量,同等质量比价格,同等价格、同等质量比服务。”的宗旨,为广大的新老客户打造出更完善的产品。

400-0312-611

保定市万嘉门窗制造有限公司

联系人:高先生 安女士

手 机:13803126757 13082332599

电 话:0312-5060303

邮 箱:13803126757@139. com

地址:河北省保定市北市区后辛庄工业区新民路39号

当前位置:断桥铝门窗的安装技巧
1定位、放线 1 positioning and discharging 先检查,后确定。在安装之前要先检查门窗洞口四周的预留孔洞或预埋铁件的位置和数量,是否与门窗框上的连接铁脚匹配吻合。若发现不符合或偏差过大时,应进行必要的修整处理。最后根据设计和施工图纸的要求,放出定位线,并确定门框位置,同时要准确地测量出地面标高于门框顶部标高以及中横框标高。 First check, then determine. Before installation, check the location of the reserved hole or the number of embedded iron parts around the opening of the door and window, and match the iron foot of the door and window frame. If any discrepancies or deviations are found to be too large, the necessary dressing should be performed. Finally, according to the requirements of the design and construction drawings, the positioning line is released and the position of the door frame is determined. At the same time, it is necessary to accurately measure the height of the ground at the top of the door frame and the elevation of the middle frame. 2安装框顶部限位槽 2 mounting frame top limit slot 限位槽的宽应大于玻璃厚度2-4mm,槽深为10-20mm。安装时,先由所弹中凡线引出两条金属装饰板边线,然后按边线进行门框顶部限位槽的安装。通过胶合垫板调整槽口内的槽深。限位槽除木衬外,采用1.5mm钢板压制、钢板焊制及铝金属型材等衬里外包不锈钢等制成。 The width of the limiting groove should be greater than that of the glass thickness 2-4mm and the groove depth is 10-20mm. When installing, the two metal decorative panel sidelines are drawn from the middle line of the projectile, and then the installation of the limiting slot on the top of the doorframe is carried out according to the sideline. The groove depth in the slot is adjusted by the bonding pad. The limiting slot is made of 1.5mm steel plate, steel plate and aluminum lining, etc. 3安装金属饰面的木底托 3 metal decorating wood bottom 首先用所弹中心线钉立门框方木,然后用胶合板确定门框柱的外形和位置,最后外包金属装饰面。外包金属装饰要注意两点,一是要把饰面对头接缝位置放在安装玻璃的两侧中门位置,二是接缝的位置必须准确并垂直。 First, use the center line to nail the door frame, then use plywood to determine the shape and position of the door frame column, and finally outlay the metal decorative surface. To outsource the metal decoration, we should pay attention to two points. First, the position of the butt joint is placed on both sides of the installation glass, and the two is the position of the seams that must be accurate and vertical.
网站建设:保定遨游公司 版权所有 © 保定市万嘉门窗制造有限公司  手机网站
联系人:安经理 服务热线:400-0312-611 电话:0312-5060303 手机:13082332599 网址:HTTP://www.bdwjmc.com
地址:河北省保定市北市区后辛庄工业区新民路39号 友链:保定保洁 护坡砖模具